Application · Churches and worship venues

House of worship amplification: intelligibility, silence and Sunday-morning reliability

A worship room asks for something different from a club: every word has to be understood at the back row, the equipment has to be inaudible when nobody is speaking, and it has to work the same way every week with a different volunteer at the desk.

Low idling powerFan noise minimisedSelectable sensitivity4-channel zones2 Ω stable

What the room actually asks of the amplifier

Four constraints decide the specification long before the wattage does.

Intelligibility before loudness

Speech consonants live in the 2–4 kHz band and are the first thing a cheap amplifier smears. A stable input stage and clean high-frequency reproduction matter more than the watt figure.

Silence between the words

In a 400-seat room the rack is often in a side room with a louvre door. Low idling dissipation means the fans stay slow — or off — through the quiet parts of a service.

Long idle hours

The system is powered for a rehearsal on Thursday and a service on Sunday. Tracking Class-D draws little at idle, so the rack does not soak the room overnight.

One operator, one desk

Where the console is already installed, the amplifier has to match it. Selectable 0.775 V / 1 V / 32 dB input on DAI lets the amplifier fit the existing gain structure instead of the other way round.

Which series fits

All six series are built in the same factory and share the same protection set. These three cover this application.

LB SERIES

LB-23 – LB-215

The installed-sound version of the tracking Class-D platform: more compact chassis, lower idling power, reduced fan noise, 300 W to 2,300 W per channel. The default for rooms where the rack is near the audience.

LB Series specs →

DAI SERIES

DAI404 / DAI406

Four channels in 2U at 400–600 W each, with the sensitivity switch that lets the amplifier drop in behind an existing mixer or DSP without re-gain-staging the room.

DAI Series specs →

D SERIES

D4300 – D4600

Four independent Class-H channels for a divisible room: main, overflow, foyer and cry room from one chassis, each pair bridgeable if the room is later combined.

D Series specs →

Comparing all six ranges side by side? Series comparison table →

A worked 400-seat room

Main left and right, two delay positions, foyer and overflow. Three chassis, one rack.

Position Amplifier Mode Output
Main L / R LB-28 stereo 8 Ω 2 × 800 W
2 delays + foyer + overflow DAI404 4 ch, 8 Ω 4 × 400 W
Stage monitors / choir LB-23 stereo 8 Ω 2 × 300 W

Six rack units total. If the room divides with a movable wall, replace the DAI404 with a D4300 so each half keeps its own zone without re-patching.

Installed on site

Photographs from commissioned rooms using Mils Audio amplification – all 52 installation photos →

Tiered lecture theatre with speech reinforcement loudspeakers and amplifier rack
Lecture theatre – speech reinforcement
Multi-purpose hall with wide-area loudspeaker coverage
Multi-purpose hall – large space coverage
Stage with proscenium arch, front fill speakers and stage lighting
Theatre stage – proscenium and front fill

What we see go wrong

Questions we get asked

How much amplifier power does a 400-seat church need?
Two 800 W channels into 8 Ω for the main system, plus four 400 W channels for delays, foyer and overflow, covers a room of that size with normal headroom. The split matters more than the total — coverage and delay zones decide intelligibility.
Can we keep our existing mixer and processor?
Yes. DAI has a selectable input sensitivity of 0.775 V, 1 V or 32 dB, so the amplifier can be matched to the console already in the rack without re-tuning the room’s gain structure.
Will the amplifier be audible in a quiet room?
LB is the installed platform: tracking rails keep dissipation low, so variable-speed fans stay slow in normal use. Place the rack away from the platform and it is inaudible at speech levels.
Do you supply 70 V / 100 V line systems?
Our amplifiers are low-impedance designs for 4–16 Ω systems. For distributed 70 V or 100 V lines we pair them with matching line transformers — send the tap wattages and we will specify the combination.
What happens if an amplifier fails on a Sunday?
Hold a spare chassis in the building. Swap takes minutes and the channel map stays valid; repair and spare-part support is handled through the support page and the contact on your order.

Send the room dimensions and seat count

Tell us the seat count, whether the room divides, and which console is already installed. We will return a channel plan and a delivered price.

Request a proposalSee all six series