Application · Cinema and theatre

Cinema amplification: fitting 5.1 and 7.1 into one chassis

A cinema rack has three constraints that rarely appear together elsewhere: eight channels of amplification in one box, a damping factor high enough to keep low frequency definition, and a fan quiet enough to live in the projection room. The JK Series was designed around those three.

6 or 8 channels5×300 W + 600 W7×400 W + 800 WDamping factor >5003U / 4U

What the room actually asks of the amplifier

Four constraints decide the specification long before the wattage does.

Channel count in one chassis

A 7.1 room needs eight amplifier channels. With three stereo amplifiers that is three mains leads, three fan paths and three chances of a ground loop. JK7418 puts all eight in one 4U chassis.

Low frequency control, not just power

Damping factor above 500 into 4 Ω keeps the sub channel from sounding slow in a room where the audience sits close to the screen wall.

A quiet projection room

Variable-speed fans and a copper toroidal transformer keep acoustic noise low enough that the rack can sit inside the room rather than in a corridor.

Speaker protection that is not optional

Cinema systems are expensive and rarely switched off. DC, short circuit, over-heat and clipping protection are standard across the JK range.

Which series fits

All six series are built in the same factory and share the same protection set. These three cover this application.

JK SERIES

JK5316 – JK7418

6- and 8-channel cinema amplifiers: JK5316 is 5 × 300 W plus a dedicated 600 W sub channel, JK7418 is 7 × 400 W plus 800 W. Pairs can be bridged if you need more on the sub.

JK Series specs →

D SERIES

D4300 – D41350

Four Class-H channels for the sub stack when one 800 W channel is not enough: the D41350 gives 5,160 W bridged into 4 Ω for two large subwoofers.

D Series specs →

DAI SERIES

DAI204 – DAI406

For retrofit rooms where the existing processor sets the gain structure, DAI’s 0.775 V / 1 V / 32 dB sensitivity switch avoids re-tuning the whole room.

DAI Series specs →

Comparing all six ranges side by side? Series comparison table →

A worked 7.1 room

A 200-seat room with stage channels, four surrounds and two subwoofers. One 4U chassis plus one 2U chassis covers the whole system.

Position Amplifier Mode Output
L / C / R + 4 surrounds JK7418 7 ch, 8 Ω 7 × 400 W
LFE (first sub) JK7418 ch 8 8 Ω 1 × 800 W
Sub pair, bridged D41350 bridged 4 Ω 2 × 5,160 W

Six rack units for the whole room, one mains feed per chassis. For a 5.1 room the single JK5316 is enough: five satellite channels at 300 W plus a 600 W sub channel.

Installed on site

Photographs from commissioned rooms using Mils Audio amplification – all 52 installation photos →

Cinema room with projection screen, LED stage lighting and surround loudspeakers
Cinema – screen, LED stage wash and surround
Ornate theatre foyer with columns, red carpet and ceiling loudspeakers
Theatre foyer – distributed ceiling audio
Theatre stage with proscenium arch, front fill speakers and stage lighting
Theatre stage – proscenium and front fill

What we see go wrong

Questions we get asked

Which JK model do I need for a 7.1 room?
JK7418: eight channels in one 4U chassis, configured as 7 × 400 W plus a dedicated 800 W subwoofer channel into 8 Ω. For a 5.1 room the JK5316 covers it with five 300 W satellite channels and a 600 W sub channel.
How much power should the subwoofer channel have?
More than any other channel in the room. The 800 W LFE channel in JK7418 drives a single sub; where the room has two large subwoofers, add a D41350 bridged to deliver 5,160 W per channel pair.
What is the damping factor of the JK Series?
Above 500 into 4 Ω and above 450 into 8 Ω, with input impedance of 10 kΩ balanced. That control is what keeps a cinema sub from sounding soft in the front rows.
Can JK channels be bridged?
Yes — every channel works independently and pairs can be bridged. The published ratings are per channel; ask us for bridging figures for the specific model and load you plan to use.
Karaoke room versus cinema: same amplifier?
Usually not. A karaoke room wants vocal presence from two or four channels; a cinema wants eight discrete channels with a dedicated LFE. JK covers both ends of that range, which is why it is specified in mixed-use venues.

Send the room plan and seat count

Tell us the speaker layout, the decoder you are using and the seat count; we will return a channel map with model numbers and a delivered price.

Request a proposalSee all six series