Selection guide

Compare the six Mils Audio amplifier series

Six ranges, one platform: channel counts from two to eight, 300 W to 2,300 W per channel, every model rated at 2 Ω. The table below is the whole range in one view — pick by channel count, chassis depth or load, not by the headline wattage.

The range at a glance

All figures are published ratings at EIA 1 kHz, 0.1 % THD. Click a series name for the full model table, dimensions and protections.

Series Output stage Ch 8 Ω per ch 4 Ω 2 Ω Bridged 4 Ω Chassis Best for
FP Series Tracking Class-D + PFC 2 300 – 1,500 W 450 – 2,300 W 600 – 3,000 W 1,200 – 6,000 W 2U, 482 × 460 × 88 mm Touring, club and sub racks where mains quality and 2 Ω loads matter
LB Series Tracking Class-D 2 300 – 1,500 W 450 – 2,300 W 600 – 3,000 W 1,200 – 6,000 W 2U, 482 × 460 × 88 mm Installed sound: hotels, theatres, worship rooms, low fan noise
JK Series Toroidal + IXYS Class-AB 6 / 8 5×300+600 W – 7×400+800 W 5×450+900 W – 7×600+1,200 W Rated per channel Per pair – ask for figures 3U / 4U, 482 mm Cinema and theatre 5.1 / 7.1 rooms from one chassis
DAI Series Class-D 2 / 4 400 – 1,000 W (2 ch), 400 / 600 W (4 ch) 600 – 1,500 W Rated per channel Up to 3,000 W (bridged 8 Ω) 2U, 482 × 460 × 88 mm Retrofit racks, conference rooms, selectable input sensitivity
D Series Class-H, 2-stage 4 300 – 1,350 W 450 – 1,950 W 600 – 2,600 W 1,200 – 5,160 W 2U, 482 × 460 × 88 mm Zone splits, bridged sub duty, 4 channels from 2U
X Series Toroidal Class-D 2 300 – 2,000 W 450 – 3,500 W 600 – 4,000 W 1,200 – 7,500 W 2U, 482 × 304 × 88 mm (3U from X1500) KTV, bars, shallow racks, heavy low-end duty

Ratings: EIA 1 kHz, 0.1 % THD. 2 Ω figures are stereo-mode per channel; bridged figures are per channel pair into 4 Ω. JK bridged figures are available on request because they depend on the satellite/sub channel split. Chassis heights: 2U = 88 mm, 3U = 132 mm.

Pick by requirement

If you already know the constraint, start here. Each row names the model that answers it.

Eight channels in one chassisA 7.1 room needs eight amplifier channels and one mains feed, not three stereo amplifiers side by side.JK7418
The most power on a single channel2,000 W into 8 Ω from a 2-channel chassis, and 4,000 W into 2 Ω.X2000
The most power from a bridged pair6,000 W into a bridged 4 Ω load, with PFC for generator use.FP15000
A rack only 304 mm deepFull-power 2-channel chassis that fits joinery and shallow flight cases.X Series
The quietest amplifier near an audienceInstalled platform: lower idling power, reduced fan speed, more compact chassis.LB Series
Matching an existing DSP outputThree-way sensitivity switch: 0.775 V, 1 V or 32 dB, without re-gain-staging the room.DAI Series
Four zones from 2UFour independent channels, bridgeable in pairs, so a divisible room needs one chassis.D Series
Sub duty on a budgetBridged 4 Ω to 5,160 W from a 4-channel Class-H chassis.D41350

By application

Each application page carries a worked rig, a channel plan and the installation photos that go with it.

Questions about the range

Which Mils series has the most channels in one chassis?
The JK Series. JK7418 puts eight channels in a single 4U chassis as 7 × 400 W plus a dedicated 800 W subwoofer channel, which covers a 7.1 room without a second amplifier. JK5316 gives six channels (5 × 300 W plus 600 W) for 5.1 rooms.
Which series gives the most power per channel?
X2000 is the highest single-channel rating in the range at 2,000 W into 8 Ω and 4,000 W into 2 Ω. For bridged duty FP15000 delivers the most from a channel pair: 6,000 W into 4 Ω.
Are all six series stable into 2 ohms?
Yes. Every model in the FP, LB, JK, DAI, D and X ranges is rated to drive 2 Ω per channel in stereo mode. Bridged operation is quoted into 4 Ω and 8 Ω only, because bridge mode halves the minimum load.
What is the difference between tracking Class-D and Class-H?
Tracking Class-D modulates the supply rails continuously to follow the audio, so dissipation stays low even at 2 Ω — that is the FP, LB and X platform. Class-H steps between two rail voltages instead, which is simpler and cheaper per channel but dissipates more at low output; that is the D Series.
Which series should I use for a shallow installation rack?
The X Series at 482 × 304 × 88 mm — 304 mm deep in 2U, against 460 mm for FP, LB, DAI and D. From X1500 upward the chassis is 132 mm high (3U) at the same depth.
Do all series share the same protection set?
Yes: DC, short circuit, overload, over-heat, clipping and power-on inrush protection across every range, with relay soft-start. Speaker protection is not an optional module on any model.
Are the power ratings measured the same way across series?
All published figures are EIA 1 kHz at 0.1 % THD, quoted per channel in stereo mode with 2 Ω figures shown separately, and bridged figures per channel pair. That is why the numbers are directly comparable between series.
Can I mix series in one rack?
Commonly done: FP on subs, DAI on monitors, D on zone feeds. All six use the same 0.775 V input sensitivity except JK (0.775 V) and DAI (switchable), so a single processor can drive a mixed rack without per-channel level correction.

Still not sure which series fits?

Send the loudspeaker list with impedance per cabinet, the number of zones and the rack depth you have. We will return a model recommendation with the channel plan and a delivered price.

Request a recommendationBrowse the catalog